Programmable Logic Controller (PLC)

 Siemens S7-1200 PLC has scalable integrated IOs, integrated PROFINET interface for programming, HMI connections, distributed IOs and distributed drive architectures. Also, it can be expanded with up to three communication modules (CM) and eight signal modules (SM). The compact SIMATIC S71200 system consists of different CPU

Siemens S7-1200 PLC has scalable integrated IOs, integrated PROFINET interface for programming, HMI connections, distributed IOs and distributed drive architectures. Also, it can be expanded with up to three communication modules (CM) and eight signal modules (SM). The compact SIMATIC S71200 system consists of different CPU

The new FX3U series is the third generation of Mitsubishi Electric successful compact PLC family. Developed for the international market, the new controllers feature a special second "adapter bus" system, which complements the existing system bus used for expansion, special function and network modules. Up to ten additional modules can be connected to this new adapter bus.

Communication ports, Micro810 ,12-point USB 2.0 (with USB adapter Micro820,20-point:10/100 Base T Ethernet port (RJ-45) RS232/RS485 non-isolated combo serial Micro830:10-point 16-point 24-point 48-point USB 2.0 (non-isolated) RS232/RS485 non-isolated combo serial

Communications B-type Peripheral USB Port Built-in RS-232C port Built-in RS-485 port

The compact, easy-to-use and low-cost solution for simple control tasks Compact, easy to operate, universally applicable without accessories "All in one": Integrated display and operator panel

Large number of on board I/Os (up to 60) CPUs Scalable CPUs to suite a variety of applications High Speed; the basic instruction execution time is up to 0.15 micro second On-Board Ethernet; Single Port for all Communication be it Programming, Interconnecting CPUs Modules HMI on network supports common Micro SD card On Board RS485 port

Communications functions One built-in peripheral port (USB 1.1): For connecting Support Software only. A maximum of two Serial Communications Option Boards can be mounted. A maximum of two Ethernet Option Boards can be mounted. When using CP1W-CIF41 Ver.1.0, one Ethernet Option Board can be mounted. Memory backup Flash memory: User programs, parameters (such as the PLC Setup), comment data, and the entire DM Area can be saved to flash memory as initial values. Battery backup: The Holding Area, DM Area, and counter values (flags, PV) are backed up by a battery. Battery service life 5 years at 25°C. (Use the replacement battery within two years of manufacture.) Built-in input terminals 40 (24 inputs, 16 outputs) 20 (12 inputs, 8 outputs) Line-driver inputs: Two axes for phases A, B, and Z Line-driver outputs: Two axes for CW and CCW Number of connectable Expansion (I/O) Units CP Expansion I/O Units: 7 max.; CJ-series Special I/O Units or CPU Bus Units: 2 max. Max. number of I/O points 320 (40 built in + 40 per Expansion (I/O) Unit × 7 Units) 300 (20 built in + 40 per Expansion (I/O) Unit × 7 Units) Interrupt inputs 8 inputs (Shared by the external interrupt inputs (counter mode) and the quick- response inputs.) 6 inputs (Shared by the external interrupt inputs (counter mode) and the quick- response inputs.) Interrupt input counter mode 8 inputs (Response frequency: 5 kHz max. for all interrupt inputs), 16 bits Up or down counters 6 inputs (Response frequency: 5 kHz max. for all interrupt inputs), 16 bits Up or down counters Quick-response inputs 8 points (Min. input pulse width: 50 μs max.) 6 points (Min. input pulse width: 50 μs max.) Scheduled interrupts 1 High-speed counters 4 inputs: Differential phases (4x), 50 kHz or Single-phase (pulse plus direction, up/ down, increment), 100 kHz Value range: 32 bits, Linear mode or ring mode Interrupts: Target value comparison or range comparison 2 inputs: Differential phases (4x), 500 kHz or Single- phase, 1 MHz and 2 inputs: Differential phases (4x), 50 kHz or Single- phase (pulse plus direction, up/down, increment), 100 kHz Value range: 32 bits, Linear mode or ring mode Interrupts: Target value comparison or range comparison Pulse outputs (models with transistor outputs only) Pulse outputs Trapezoidal or S-curve acceleration and deceleration (Duty ratio: 50% fixed) 4 outputs, 1 Hz to 100 kHz (CCW/CW or pulse plus direction) Trapezoidal or S-curve acceleration and deceleration (Duty ratio: 50% fixed) 2 outputs, 1 Hz to 1 MHz (CCW/CW or pulse plus direction) 2 outputs, 1 Hz to 100 kHz (CCW/CW or pulse plus direction) PWM outputs Duty ratio: 0.0% to 100.0% (Unit: 0.1%) 2 outputs, 0.1 to 6553.5 Hz (Accuracy: ±5% at 1 kHz) Built-in analog I/O terminals 4 analog inputs and 2 analog outputs None Analog control 1 (Setting range: 0 to 255) External analog input 1 input (Resolution: 1/256, Input range: 0 to 10 V), not isolated Note: The memory areas for CJ-series Special I/O Units and CPU Bus Units are allocated at the same as for the CJ-series. For details, refer to the CJ Series catalog (Cat. No. P052). last update: January 05, 2015

Digital Input Medium speed (20KHz): 6 POINT Medium speed (Total 5KHz): 6 POINT DIGITAL OUTPUT: 8 POINT Built-in: 1 port (Port0, USB or RS232) Expandable: 2 ports (Port1~2, RS485 or RS232 or Ethernet)